inInfinityFlow3D

InfinityFlow3D

@infinityflow3d

Effortless automation for a seamless 3D printing experience.

InfinityFlow3D เป็นครีเอเตอร์ TikTok มีผู้ติดตาม 16.6K และยอดไลก์ 153.3K วิดีโอมียอดวิวเฉลี่ย 19.1K ครั้ง อัตราการมีส่วนร่วม 2.3% แฮชแท็กที่ใช้บ่อยที่สุด: #3dprinting #printfarm และ #3dprinter

https://infinityflow3d.com/pages/links-page?utm_source=social&utm_medium=tiktok&utm_id=&utm_content=bio
16.6K
ผู้ติดตาม
0
กำลังติดตาม
153.3K
ยอดไลก์
19.1K
ยอดวิวเฉลี่ย
อัตราการมีส่วนร่วม: 2.3% สหรัฐอเมริกา 🗣️ อังกฤษ
16.6K
ผู้ติดตาม
153.3K
ยอดไลก์รวม
19.1K
ยอดวิวเฉลี่ย
404
วิดีโอ

การเติบโตและคาดการณ์

อัปเดตล่าสุดคาดการณ์ 7 วันคาดการณ์ 30 วัน
ผู้ติดตาม16.6K▲ 🔒 Pro🔒 Pro
ยอดไลก์รวม153.3K▲ 🔒 Pro🔒 Pro
วิดีโอ404🔒 Pro🔒 Pro
ยอดวิวเฉลี่ย19.1K▼ 🔒 Pro🔒 Pro

ปลดล็อกรายงานฉบับเต็ม

อีเมลติดต่อ ประวัติการเติบโตและการคาดการณ์ และคลังวิดีโอทั้งหมด อยู่ในแพ็กเกจ Pro

ดูรายงานฉบับเต็ม →

Pro ใช้ฟรีในช่วงเบต้า: เริ่มทดลองใช้ได้เลย ไม่ต้องใช้บัตรเครดิต

รายได้โดยประมาณ

ค่าโพสต์สปอนเซอร์โดยประมาณ: $80 ถึง $400 คำนวณจากราว 5–25 ดอลลาร์ต่อผู้ติดตาม 1,000 คน เป็นเพียงการประมาณจากขนาดผู้ชม ไม่ใช่รายได้ที่รายงานจริง

อัปเดตล่าสุด:

โปรไฟล์ TikTok

วิดีโอล่าสุด

วิดีโอล่าสุด: 2026-10-23

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing
▶
▶ 6K ❤ 0 💬 0

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm
▶
▶ 16.8K ❤ 0 💬 0

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing
▶
▶ 3.3K ❤ 0 💬 0

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

คำถามที่พบบ่อย

InfinityFlow3D มีผู้ติดตามกี่คน

ณ วันที่ 2026-10-24 InfinityFlow3D (@infinityflow3d) มีผู้ติดตามบน TikTok 16.6K

ครีเอเตอร์ที่คล้ายกัน

อันดับครีเอเตอร์ TikTok ในสหรัฐอเมริกา

ดูทั้งหมด →
charli d’amelio @charlidamelio
#2

orca enthusiast meg thee stallion fan i post on youtube on saturdays (for the most part)

ผู้ติดตาม
160.4M
ยอดไลก์
12.4B
ยอดวิว
3.6M
มีส่วนร่วม
2.3%