@infinityflow3d TikTok: 16.6K подписчиков сегодня

16.6K

Подписчики

153.3K

Всего лайков

19.1K

Ср. просмотры

404

Видео

Рост и прогноз

	Обновлено	Прогноз на 7 дней	Прогноз на 30 дней
Подписчики	16.6K	▲ 🔒 Pro	🔒 Pro
Всего лайков	153.3K	▲ 🔒 Pro	🔒 Pro
Видео	404	🔒 Pro	🔒 Pro
Ср. просмотры	19.1K	▼ 🔒 Pro	🔒 Pro

Откройте полный отчёт

Контактный e-mail, история роста и прогнозы, а также полный архив видео доступны в Pro.

Смотреть полный отчёт →

Pro бесплатен на время бета-версии: попробуйте без банковской карты.

Оценка доходов

Оценочная цена рекламной публикации: от $80 до $400, исходя из примерно 5–25 долларов за 1000 подписчиков. Это оценка по размеру аудитории, а не заявленный доход.

🔒 Pro: rank history, video velocity, growth signals, brand deals and lookalike creators

Обновлено: 2026-10-25 03:27 UTC

Профиль в TikTok

Последние видео

Последнее видео: 2026-10-23

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

▶

▶ 6K ❤ 0 💬 0

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

▶

▶ 16.8K ❤ 0 💬 0

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

▶

▶ 3.3K ❤ 0 💬 0

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

🔒 Ещё 3 видео в Pro →

Открыть @infinityflow3d в TikTok 🚀