InfinityFlow3D (@infinityflow3d) TikTok: 16.6K pengikut hari ini

16.6K

Pengikut

153.3K

Jumlah suka

19.1K

Purata tontonan

404

Video

Pertumbuhan & Ramalan

	Kemas kini terakhir	Ramalan 7 hari	Ramalan 30 hari
Pengikut	16.6K	▲ 🔒 Pro	🔒 Pro
Jumlah suka	153.3K	▲ 🔒 Pro	🔒 Pro
Video	404	🔒 Pro	🔒 Pro
Purata tontonan	19.1K	▼ 🔒 Pro	🔒 Pro

Buka laporan penuh

E-mel hubungan, sejarah pertumbuhan dan ramalan, serta arkib video penuh tersedia dalam Pro.

Lihat laporan penuh →

Pro percuma sepanjang beta: mulakan percubaan, tanpa kad kredit.

Anggaran pendapatan

Anggaran kadar bagi setiap hantaran penajaan: $80 hingga $400, berdasarkan kira-kira 5 hingga 25 dolar bagi setiap 1,000 pengikut. Ini anggaran berdasarkan saiz audiens, bukan pendapatan yang dilaporkan.

🔒 Pro: rank history, video velocity, growth signals, brand deals and lookalike creators

Kemas kini terakhir: 2026-10-25 03:27 UTC

Profil TikTok

Video terkini

Video terbaharu: 2026-10-23

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

▶

▶ 6K ❤ 0 💬 0

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

▶

▶ 16.8K ❤ 0 💬 0

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

▶

▶ 3.3K ❤ 0 💬 0

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

🔒 3 lagi video dalam Pro →

Lihat @infinityflow3d di TikTok 🚀