inInfinityFlow3D

InfinityFlow3D

@infinityflow3d

Effortless automation for a seamless 3D printing experience.

InfinityFlow3D is a TikTok creator in the United States with 16.6K followers and 153.3K likes. Their videos average 19.1K views, an engagement rate of 2.3%. Most-used hashtags: #3dprinting, #printfarm and #3dprinter.

https://infinityflow3d.com/pages/links-page?utm_source=social&utm_medium=tiktok&utm_id=&utm_content=bio
16.6K
Followers
0
Following
153.3K
Likes
19.1K
Avg views
Engagement: 2.3% United States 🗣️ English
16.6K
Followers
153.3K
Total likes
19.1K
Avg views
404
Videos

Growth & Forecast

Last updated7-day forecast30-day forecast
Followers16.6K▲ 🔒 Pro🔒 Pro
Total likes153.3K▲ 🔒 Pro🔒 Pro
Videos404🔒 Pro🔒 Pro
Avg views19.1K▼ 🔒 Pro🔒 Pro

Unlock the full report

Contact email, growth history and forecasts, and the full video archive are part of Pro.

View full report →

Pro is free during the beta: start a trial, no credit card required.

Estimated earnings

Estimated rate per sponsored post: $80 to $400, based on roughly $5 to $25 per 1,000 followers. This is an estimate from audience size, not reported income.

Last updated:

TikTok profile

Recent videos

Latest video: 2026-10-23

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing
▶
▶ 6K ❤ 0 💬 0

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm
▶
▶ 16.8K ❤ 0 💬 0

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing
▶
▶ 3.3K ❤ 0 💬 0

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

Frequently asked questions

How many followers does InfinityFlow3D have?

InfinityFlow3D (@infinityflow3d) has 16.6K TikTok followers as of 2026-10-24.

Similar creators

Top TikTok Creators in the United States

View all →
charli d’amelio @charlidamelio
#2

orca enthusiast meg thee stallion fan i post on youtube on saturdays (for the most part)

Followers
160.4M
Likes
12.4B
Views
3.6M
Engage
2.3%