InfinityFlow3D (@infinityflow3d) TikTok: フォロワー16.6K 今日

16.6K

フォロワー

153.3K

いいね合計

19.1K

平均再生数

404

動画

成長と予測

	最終更新	7日間予測	30日間予測
フォロワー	16.6K	▲ 🔒 Pro	🔒 Pro
いいね合計	153.3K	▲ 🔒 Pro	🔒 Pro
動画	404	🔒 Pro	🔒 Pro
平均再生数	19.1K	▼ 🔒 Pro	🔒 Pro

完全版レポートを解除

連絡先メール、成長履歴と予測、全動画アーカイブはProでご利用いただけます。

完全版レポートを見る →

ベータ期間中はProが無料。クレジットカード不要でお試しいただけます。

推定収益

タイアップ投稿1件あたりの推定単価：$80〜$400（フォロワー1,000人あたり約5〜25ドルで計算）。オーディエンス規模からの推定であり、公表された収入ではありません。

🔒 Pro: rank history, video velocity, growth signals, brand deals and lookalike creators

最終更新: 2026-10-25 03:27 UTC

TikTokプロフィール

最近の動画

最新の動画：2026-10-23

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

▶

▶ 6K ❤ 0 💬 0

Does anyone else have a pile like this? 😂 Too much filament to throw away, but not enough to trust on a full print. We use the S1+ to burn through all of these instead of letting them sit forever. #3DPrinting #PrintFarm #Filament #FDMPrinting #AdditiveManufacturing

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

▶

▶ 16.8K ❤ 0 💬 0

We waited for something dramatic to happen when the spool ran out… Nothing did. The S1+ automatically loaded the next spool and the printer just kept going like nothing happened. Honestly, that’s exactly how it should be. #3DPrinting #3DPrinter #InfinityFlow3D #Prusa #PrintFarm

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

▶

▶ 3.3K ❤ 0 💬 0

That last little bit of filament always feels way more dramatic than it should. Normally, once it disappears into the printer, you’re either there to swap the spool… or you’re hoping the print can wait. With the S1+, it just loads the next spool and keeps going. The end of the spool isn’t the end of the story. #3DPrinting #3DPrinter #Filament #PrintFarm #AdditiveManufacturing

🔒 Proでさらに3本の動画 →

TikTokで@infinityflow3dを見る 🚀